Letters within letters! Type an uppercase letter followed by a lowercase letter to nest them. Type a period for an inner square, and > for an outer square.
This was an experiment from several years ago that I found half-finished while looking for potential CounterComp entries. I added missing letters and quite dramatically improved the existing ones. It's not perfect, and some combinations don't work so well (I'm particularly unhappy with capital I), but I think it turned out pretty well nonetheless.
Beware: for some reason, the downloaded font is huge-about 6 times the height of most other fonts-which makes it look horrible in e.g. MS Word, due to the pixel optimization at "small" sizes. I'm not sure what causes this, and consequentially, I don't know how to fix it.
fs Stainless Square
==================================================================
Basically just fs Stainless but more geometric and sharp
I use composited bricks to closely fit with the connects since there are no sharp wedges for the connects
I came up with an original high-res design, then brickswapped to turn everything into square bricks. The result sort of reminds me of Proxima Punch Pixel Squared, but less art deco and more computer-esque. It has a really old and naive look to it which could make it good for retro-terminal use.
"Buttons Foe" = "Obtuse Font". Not only is it an obtuse font in look and construction, it's reminescent of an era when computers were thought of as adversarial, magic voodoo boxes. So both the name and the anagram are equally applicable. :^)
An experiment to see if 3x3 fonts are more legible when drawn in negative space. I consider this to be not only a success, but also the most readable 3x3 design I have seen - particularly the uppercase.
The successors Megashark and S.D.M.G. are more useable and more stylish respectively, while Minishark strikes a good balance.
This is considered an E3x3 because, while it's created in a 5x5 grid, it has an effective drawing area of only 3x3. The outermost square only has pixels drawn in it when the interior design dictates such.
Stained-glass blackletter Frankenfont thing. :D
UC cloned to LC to make this easier to use...
This is a clone of Chimera SpineA design that looks like a top-down view of ziggurats!
I composited the diacritics so they'd fit into place, but this means that most anything non-English needs to be pretty large to be unambiguously read...
Original size: 15pt
*
A font which has a spurless, sans-serif, pixelated polygonal look which is somewhat reminescent of fonts used in VHS technology.
A lot of applied science went into this design. It's designed to remain legible on all media in all use conditions, provided that one uses the original size or a multiple thereof. Numerous technologies and mediums were employed to realize this objective.
"Diaspora" was tested and refined for use with/on/against:
• CRT, LCD & e-Ink screens
• image formats & compressed imagery (GIF, JPG)
• printers (inkjet, bubble jet, laserjet, & thermal)
• analog video & multi-generational copies (VHS, Super 8)
• digital video (AVI, MP4, MPEG, WEBM, WMV)
• 3D and voxel models (Blender, MagicaVoxel, POV-Ray)
• dynamic scaling hardware (game consoles and capture devices)
• imagery plugins & filters, including image degraders
• image scaling/interpolation hardware & software
• image recognition hardware & software
These all have traits which degrade, distort, compress, glitch, or otherwise alter imagery in various ways. This design aims to minimize the loss of legibility from these effects and to attain the best scores possible in various forms of imagery analysis. So far, this has proved extremely useful, as it can remain fully legible even when extreme JPG or video compression are applied to it thousands of times.
A piece of software I helped write, called the Marinan Imagery Deconstruction AI System (MIDAS), is being used on captured images of this font. The end objective is to realize the design which has the best all-around Marinan Interpretability Value (MIV) for all the tested platforms - the design which is considered by MIDAS to be the most legible in the most media under the broadest range of use conditions and quality levels.
MIDAS uses a set of considerations made with both humans and computers in mind, so a high MIV does not necessarily equal a better font - it just means one that the system thinks is easier to visually interpret. Note the use of the phrase "visually interpret" as opposed to "read". MIDAS tries to determine how well people and computers can tell what shapes are, not how much enjoyment they'll get from reading or how much strain they might undergo while doing it.
*
VERSION HISTORY:
1.0.0 - initial release.
1.0.1 - More Latin support added.
1.0.2 - First batch of tests run.
1.0.3 - gjy5&ßẞ were improved, some glyphs added.
1.0.4 - Second batch of tests run. Space width reduced.
1.0.5 - Experimentally converted to a rounded spurless design, then converted back to a plain spurless after testing. A few new ligatures were added.
1.0.6 - Cyrillic and Greek enter development. Many of these letters must be altered to be distinct from their Latin counterparts.
1.0.7 - Some spacing values changed to increase internal consistency. More difficult tests are being devised. However, since only I seem interested in this type of work, this project is going on hiatus for some time.
*
See also: AMFA, a font built with similar considerations in mind
The first of a kind - an experimental font made with the new pizza slice brick. :D
Somehow it makes me think of jukeboxes, particularly letters like "A" and "O" which have the same sort of "mosaic lighting" look which many jukeboxes have.
No filters, just nudging!
I wondered what a plain version of Candylander would look like, so I made this. :D
I think a fully half-arc version could look even more stylish than this! Hope to find time to create one soon. (EDIT: Done, see Migrator)
This is a clone of CandylanderExperimental brush/pen thing. Has a slightly spooky look. Because of their tapering curves, many glyphs can render with a "split" or "stencil" look about them. This is due to software-imposed limitations on vector rendering. Designs which share this property can be considered Pseudostencils.
This design is not informed or inspired by any existing typographical traditions. I set out to make the "claw" bricks (as I call them) into a font and this is the result.
*
A dashed line design made with the new half-arc bricks. The emphasized spurs/stems and off-kilter geometry give it a quirky, almost handwritten quality. Its striped appearance makes me think of candy as well as the Cheshire Cat, thus the name. :D
I doubt the upper case would look as cute as the lower. So I've cloned all LC to UC to make this easier to use...
Experimental 5x3 font. This went through quite a few iterations! The result is surprisingly readable, but still not quite something I'd want to use as a chat font.
In making this I did my best to avoid compression and truncation, trying instead to use the interpretation of light as my guide. Many glyphs don't look much at all like what they represent, but as my eye glides over them, they make sense and I read them without issue.