Searching for more “Stencil” fonts?
Buy and download “Stencil” fonts at MyFonts.
The current month seems to hold a meaning of threads: of fog, dew covered spiders' webs, barely-there things, feint perceptions defying scientific understanding and fine links with ancestors, to keep us in the present and enable open minds and caring souls to better the future. This abstract interpretation of Halloween has been designed to echo the traditionally mysterious mood to show the past (known glyphs, earlier FS bricks) linked in the present (on paper, in the FS previews, and using some of Meek's newest bricks I experiment with in this design) to create future (text will carry meaning to the reader, diversity of thought not experienced until after every glyph is finished, and beauty of text flow is visible only after it has been written). Totally within my personal plan for Night Pegasus' work: adventurous, alternative, divergent, different, exploring, experimental, unusual -- after all, the flying horse is free to visit any time any item or existence in this universe and any place in Fontstruct, to discover and weigh possibilities, to create its future from the past in it's present body and mind, and it does this cloaked in black as deepest night, undiscovered unless someone has their feelers tuned into mystery and taps into experiences of presence.
:.:.:.: Information to help you when using this font :.:.:.:
If a LC glyph follows a UC glyph: you need to use the space bar 6X to get the correct letter space (it will then match the natural spacing between LC); using only LC glyphs (or only UC glyphs) will give satisfactory text results as letter space is set by the programming. But you'll need to manually add the word space you want: between UC (or LC) words a minimum of 3 space taps for a just visible gap, use the space bar 6x for good spacing. Experiment!
Note: the full stop and comma have a line on the baseline to link with UC. There might be no need for a 'space' after those two marks even on LC? The apostrophy has a short line to link it to previous/following UC glyphs (note those link lines retain the meaning of the glyph when used with LC glyphs or an LC following an UC glyph).
SPACE BAR = a 1px space; tap 3x to get a small word space that's obvious
% key = a set of reasonably wide lines to match upper case verticals
_underscore = a space consisting of a long single line on base line only
I'm trying to figure out some diacritics before the 31st so this remains WIP
When my mother was young (and specially after my birth) she supplemented the family's income from home by typing for students and businesses. When I was a student I used the same machine for my assignments, lesson plans and thesis. The years were not kind to the machine, the mechanics rusted or broke, the letters worn with frayed edges or disintegrating serifs and fine lines. Ruth's typewriter is a declaration of my appreciation of many years of service the brave little machine gave... As you can see I clearly didn't get the letters repaired ;) The font looks like I rearranged and glued down what was left of the raised surfaces, to continue using the typewriter and give my words a very modern look ;)) A "grunge-writer" ?? Did you notice that no typewriters were ever sold with this kind of modern destructured typefaces?! ;)
Since I started this font many years ago (Ruth was very amused and appreciated this hommage) this work has now become a memorial to her
Dot-line thin font. Inspired by Stag Dot.
Modern geometric serif(slab?) font.
See more: https://www.fontstruct.com/fontstructions/show/1675889/prototype-2-0-1
https://fontstruct.com/fontstructions/show/749833/fs_dot_serif
~Type an uppercase letter and type the corresponding (or some other) lowercase letter to fill in the shape.
You can use the uppercase letters to form one word and type the lowercase fill letters to form the same or another word, or fill with a blanking glyph to complete the letter with no center letter. So, two types of letters are possible with this one font.
The letters had to be designed such that the uppercase could read as a letter without a center fill on it's own, or filled with blank glyph, or with a center letter. In doing so, the font turned auto-stencil and auto-monospaced. Also, since the unfilled uppercase read as the correct letter with the hole in it, this fs can be said to have three fonts in it.
The gaps are 1/8 brick; the thickness of the inner letter strokes is 2/8 brick. Therefore, this limitation meant that the glyphs with a stroke in the horizontal center can either be lined up with the left side blocks or the right side one. Therefore, 3/8 brick thickness I and T are provided on { and }.
Letter couples are as follows: Aa Bb Cc Dd Ee Ff Gg Hh Ii or I{ Jj Kk Ll Mm Nn Oo Pp Qq Rr Ss Tt or T} Uu Vv Ww Xx Yy Zz
Number couples are: !1 @2 #3 $4 %5 ^6 &7 *8 (9 )0
Blanks: ~, space
Center blank: `
Pipe: = (which will offset the monospacing)
Others; ? is at ?/ ! is at |\
Punctuations are where they are supposed to be: . , ; : ' " ’ ” ‘ “ -
Sample: Type the following in User Input to see the font as it is supposed to be: A`AaB`BbC`CcD`DdE`EeF`FfG`GgH`HhI`IiI{J`JjK`KkL`LlM`MmN`NnO`OoP`PpQ`QqR`RrS`SsT`TtT}U`UuV`VvW`WwX`XxY`YyZ`Zz!`!1@`@2#`#3$`$4%`%5^`^6&`&7*`*8(`(9)`)0?`?/|`|\)-)+~_<>=
6 bricks tall.
The sample is a font pun: TWO in ONE.
PS: Not sure how future it is.